The Data Link Layer and IEEE

The second-lowest layer (layer 2) in the OSI Reference Model stack is the data link layer, often abbreviated “DLL” (though that abbreviation has other meanings as well in the computer world). The data link layer, also sometimes just called the link layer, is where many wired and wireless local area networking (LAN) technologies primarily function. For example, Ethernet, Token Ring, FDDI and 802.11 (“wireless Ethernet” or “Wi-Fi’) are all sometimes called “data link layer technologies”. The set of devices connected at the data link layer is what is commonly considered a simple “network”, as opposed to an internetwork.

When we talk about Local Area Network (LAN) technology the IEEE 802 standard may be heard. This standard defines networking connections for the interface card and the physical connections, describing how they are done. The 802 standards were published by the Institute of Electrical and Electronics Engineers (IEEE). The 802.3 standard is called ethernet, but the IEEE standards do not define the exact original true ethernet standard that is common today. There is a great deal of confusion caused by this. There are several types of common ethernet frames. Many network cards support more than one type.

The ethernet standard data encapsulation method is defined by RFC 894.

Network Protocol Levels

---

The International Standards Organization (ISO) has defined a standard called the Open Systems Interconnection (OSI) reference model. This is a seven layer architecture listed below. Each layer is considered to be responsible for a different part of the communications. This concept was developed to accommodate changes in technology. The layers are arranged here from the lower levels starting with the physical (hardware) to the higher levels.

1. Physical Layer - The actual hardware.
2. Data Link Layer - Data transfer method (802x ethernet). Puts data in frames and ensures error free transmission. Also controls the timing of the network transmission. Adds frame type, address, and error control information. IEEE divided this layer into the two following sublayers.
   1. Logical Link control (LLC) - Maintains the Link between two computers by establishing Service Access Points (SAPs) which are a series of interface points. IEEE 802.2.
   2. Media Access Control (MAC) - Used to coordinate the sending of data between computers. The 802.3, 4, 5, and 12 standards apply to this layer. If you hear someone talking about the MAC address of a network card, they are referring to the hardware address of the card.

TCP/IP Ports and Addresses

IPv6 is an enhancement to the IPv4 standard due to the shortage of internet addresses. The dotted notation values are increased to 12 bit values rather than byte (8 bit) values. This increases the effective range of each possible decimal value to 4095. Of course the values of 0 and 4095 (all bits set) are generally reserved the same as with the IPv4 standard.

---

An Example Network

In the diagram below, the earlier hardware wiring example is modified to show the network without the hubs. It also shows IP addresses assigned to each interface card. As you can see there are two networks which are 192.168.1.x and 192.168.2.x. Machines A through F are on network 192.168.1.x. The machines X and Z are on network 192.168.2.x, and machine G has access to both networks.

TCP and IP are two seperate protocols. IP (Internet Protocol) is a network layer protocol, while TCP (Transmission Control Protocol) is a transport layer protocol. Every computer and network device attached to the Internet has at least one IP address. For example, the IP address of this web server is 66.37.153.81. Every computer and network device attached to the Internet has at least one IP address. For example, the IP address of this web server is 66.37.153.81. Then, within each of those IP addresses, each computer and network device will have a number of TCP ports. For example, the web server software on this web server responds on TCP port 80 and the mail server software on the same computer

Hardware Connections in Networking

n the diagram, machine G has two network cards, eth0 and eth1. The cards eth1 and eth0 are on two different networks or subnetworks. Unless machine G is programmed as a router or bridge, traffic will not pass between the two networks. This means that machines X and Z cannot talk to machines A through F and vice versa. Machine X can talk to Z and G, and machines A though F can talk to each other and they can talk to machine G. All machines can talk to machine G. Therefore the machines are dependent on machine G to talk between the two networks or subnets.

Each network card, called a network interface card (NIC) has a built in hardware address programmed by its manufacturer. This is a 48 bit address and should be unique for each card. This address is called a media access control (MAC) address. The media, in our specific case will be the ethernet. Therefore when you refer to ethernet, you are referring to the type of network card, the cabling, the hubs, and the data packets being sent. You are talking about the hardware that makes it work, along with the data that is physically sent on the wires.

There are three types of networks that are commonly heard about. They are ethernet, token-ring, and ARCnet. Each one is described briefly here, although this document is mainly about ethernet.

---

Ethernet:

The network interface cards share a common cable. This cable structure does not need to form a structure, but must be essentially common to all cards on the network. Before a card transmits, it listens for a break in traffic. The cards have collision detection, and if the card detects a

Network Topology

Network topology is the study of the arrangement or mapping of the elements (links, nodes, etc.) of a network, especially the physical (real) and logical (virtual) interconnections between nodes.

A local area network (LAN) is one example of a network that exhibits both a physical topology and a logical topology. Any given node in the LAN will have one or more links to one or more other nodes in the network and the mapping of these links and nodes onto a graph results in a geometrical shape that determines the physical topology of the network. Likewise, the mapping of the flow of data between the nodes in the network determines the logical topology of the network. It is important to note that the physical and logical topologies might be identical in any particular network but they also may be different.

Any particular network topology is determined only by the graphical mapping of the configuration of physical and/or logical connections between nodes. LAN Network Topology is, therefore, technically a part of graph theory. Distances between nodes, physical interconnections, transmission rates,